ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||20 April 2004|
|PDF File Size:||20.60 Mb|
|ePub File Size:||20.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Chemical analysis may be accomplished by wet chemical or instrumental procedures. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? When none has been speci?
If spectrometric procedures are used, the sample shall asttm exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal. Originally approved in The minimum cladding thickness for shear testing shall be 0. The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. A number in parentheses indicates the year of last reapproval.
ASTM A265 GR 1 titanium alloy strip sheet plate
The properties thus determined shall meet all of the tensile test requirements for the base steel. All other tensile test requirements of the speci? Ultrasonic Examination in accordance with Speci?
These bend tests shall be made in the manner of the asym tests indicated in Fig. Workmanship Finish, and Appearance This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.
Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci?
Gage Length cladding and the base steel shall be machined so as to maintain the same ratio of clad metal to base steel as is maintained in the plate, except that the thickness of the clad material astn not be reduced below 1? Areas within 1 in. Historical Version s – view previous versions of standard.
ASTM A265 Clad Plate
The reduced section shall have a gradual taper from the ends toward the center, with the ends 0. Testing for shear strength for clad plates with minimum cladding thickness of 0.
General Requirements for Delivery Permissible Variations Metric Equivalents in.
This standard has been approved for use by agencies of the Department of Defense. Other tests may be performed by agreement between the supplier and the purchaser. If the requirements of this speci? The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding.
A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci? The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications.
Historical Version s – view previous versions of standard Translated Version s: Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer.
The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.
The steel shall be made by the open-hearth, electric furnace with separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes.
ASTM A – 03 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate
Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition. Last previous edition approved in as A — In reducing the thickness of the specimen, both the alloy 3 Metric Equivalents in. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Several sstm those considered suitable for use with this speci? Materials and Manufacture 5. Approved May 1, The base metal shall conform to the chemical requirements of the speci? NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci? Each specimen shall be in the? Link to Active This link will always route to the current Active version of the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.